VS501Z spa packs or replacement circuit boards are shipped as they come from the factory (all white wire jumpers on WHT AC). The customer or installer needs to set the white wires to the appropriate voltage that the load device plugged into its corresponding receptacle requires.  So for example if your hot tub has a 2-speed pump 1 that is 230 volts, the W1 white wire needs to be moved to any RED AC terminal.  When on RED AC output will be 230 volt, when on WHT AC it will be 120 volt.

Also the DIP switches need to be set to match your situation.  If a replacement situation (i.e. you already had a VS501Z) then just set the dip switches the way they were on the old unit.  very old VS501 did have the A% dip switch acting opposite to how they act on new units.

 

hope this helps

Dieter

ok great got it working now my pump had the seal go on it so I had to shut everything down and get that replaced.  My next question is I already did the original start up with the new spa pak where it primed then checked water temperature, etc.  Because I flipped the breaker off for 2 days when i hook the pump back up does it automatically do the original start up.  My concern is that I don't want the elements to go on when no water is on them I would like it to restart like it originally did but I read that it has a memory and will just go back to the last temperature it was at.  Is there a reset button that I can hit that will just start it back to the beginnning(like I turned it on for the 1st time)
From: cedartubsdirect <[email protected]>
To: Jason <[email protected]>
Sent: Monday, October 8, 2012 6:26:57 PM
Subject: [CTT: #1062] Reply to your query - cedartubsdirect

Hi Jason, A rep replied to a support ticket with cedartubsdirect.
ISSUE #1062
----------------- Content of the Ticket -----------------
Subject : retofit kit
Message : VS501Z spa packs or replacement circuit boards are shipped as they come from the factory (all white wire jumpers on WHT AC). The customer or installer needs to set the white wires to the appropriate voltage that the load device plugged into its corresponding receptacle requires.  So for example if your hot tub has a 2-speed pump 1 that is 230 volts, the W1 white wire needs to be moved to any RED AC terminal.  When on RED AC output will be 230 volt, when on WHT AC it will be 120 volt. Also the DIP switches need to be set to match your situation.  If a replacement situation (i.e. you already had a VS501Z) then just set the dip switches the way they were on the old unit.  very old VS501 did have the A% dip switch acting opposite to how they act on new units.   hope this helps Dieter
------------------------------------------------------------------
In the meantime, you can update the ticket by replying to this mail. You can also update this ticket using the URL : Click Here
Thanks for using our Service. Regards
cedartubsdirect

When you turn the power back on, the spa pack will remember the last settings (i.e., what the temperature setting was, what the filter cycle duration was set at and what mode it was set to).  This is the last adjustment you made.  If you want it back to the factory default setting, you have to do a memory reset.  Factory default is Standard mode, 2 Hr filter cycle and temperature set to 100F.

 

Dieter

ok how do you do a memory reset?
From: cedartubsdirect <[email protected]>
To: Jason <[email protected]>
Sent: Friday, October 12, 2012 1:40:42 PM
Subject: [CTT: #1062] Reply to your query - cedartubsdirect

Hi Jason, A rep replied to a support ticket with cedartubsdirect.
ISSUE #1062
----------------- Content of the Ticket -----------------
Subject : retofit kit
Message : When you turn the power back on, the spa pack will remember the last settings (i.e., what the temperature setting was, what the filter cycle duration was set at and what mode it was set to).  This is the last adjustment you made.  If you want it back to the factory default setting, you have to do a memory reset.  Factory default is Standard mode, 2 Hr filter cycle and temperature set to 100F.   Dieter
------------------------------------------------------------------
In the meantime, you can update the ticket by replying to this mail. You can also update this ticket using the URL : Click Here
Thanks for using our Service. Regards
cedartubsdirect

Memory Reset using J43 Jumpers

 

J43 located above and to the right of the DIP switches, is left open (black jumper is on one pin only), to enable persistent memory.  Persistent memory will retain the last temperature, filter cycle and power mode settings, even after a power failure.  A persistent memory reset should be performed after any change to the dip switch settings.  To reset the memory (and settings) back to factory default, turn off power, jumper both J43 pins, turn power on until “Pr” appears, power off and reset jumper to be on one pin only.

 

 

great did it and worked quite easy.  On a side note this purchase I got last week was to come with a light which it did however it came with no cover or anything for the inside of this tub is this incorrect.  Should the whole retro fit kit "balbo vs502z have come with a cover for the inside of the tub too?

From: cedartubsdirect <[email protected]>
To: Jason <[email protected]>
Sent: Friday, October 12, 2012 8:23:21 PM
Subject: [CTT: #1062] Reply to your query - cedartubsdirect

Hi Jason, A rep replied to a support ticket with cedartubsdirect.
ISSUE #1062
----------------- Content of the Ticket -----------------
Subject : retofit kit
Message : Memory Reset using J43 Jumpers   J43 located above and to the right of the DIP switches, is left open (black jumper is on one pin only), to enable persistent memory.  Persistent memory will retain the last temperature, filter cycle and power mode settings, even after a power failure.  A persistent memory reset should be performed after any change to the dip switch settings.  To reset the memory (and settings) back to factory default, turn off power, jumper both J43 pins, turn power on until “Pr” appears, power off and reset jumper to be on one pin only.    
------------------------------------------------------------------
In the meantime, you can update the ticket by replying to this mail. You can also update this ticket using the URL : Click Here
Thanks for using our Service. Regards
cedartubsdirect

The retrofit comes with the light harness only.  The actual light wall fitting you are thinking about needs to be part of your hot tub.  You then insert the light bulb holder into the existing light wall fitting.  If your tub doesn't have one and you wish to use the light, then you would 1st have to install an appropriate light wall fitting.

Dieter